ROUTER V519
  • About EXVIST
  • 📌GETTING STARTED
    • Introduction
    • Interfaces
    • Quick Start
  • ✨Configuration
    • Dashboard
    • Resource
    • Interface
    • Network
      • LTE
      • LAN
      • AP Client
      • Routing Table
      • Source Routing Table
      • Port Map
      • Firewall
      • ALG
      • Hosts
    • Wireless
      • SSID
      • Channel
      • Advanced
      • ACL
    • Station Control
      • Station List
      • Station Address Bind
      • Station Wake Up
      • Internet Control
      • Station Internet Control
      • Access Control
      • Station Access Control
      • Traffic Reference
      • Station Traffic Control
      • Default Traffic Control
    • Application
      • DDNS
      • HA(VRRP)
      • OpenVPN Client
      • LTE GPS
      • Serial#1
      • JT808 GPS Report
      • UPNP
      • IGMP Proxy
      • Multicast Routing
      • L2TP Client
      • PPTP Client
      • GRE Tunnel
    • System
      • Device
      • Configure
      • Software
      • Password
      • Web Server
      • Telnet Server
      • SSH Server
      • Manage Server
      • Auto Reboot
      • LED/IO Control
    • Debug
      • Syslog
      • Terminal
      • LTE Adjust
      • Development
      • SDK
      • Crontab
      • Inittab
      • Uninittab
      • Jointtab
      • Service
      • COM Interface
  • 📤FIRMWARE
    • Download
  • 🎆RESOURCES
    • FAQ
    • Official Store
    • YouTube Channel
Powered by GitBook
On this page
  • Device
  • Operation Mode
  • LTE Gateway
  • Gateway
  • 2.4G WISP
  • AP
  • Mix

Was this helpful?

  1. Configuration
  2. System

Device

PreviousSystemNextConfigure

Last updated 4 years ago

Was this helpful?

Device

In this section, it allows the user to change the operation mode and language. Please check below details:

Operation Mode

  • 5x operation modes can be selected: LTE Gateway (By Default), Gateway, 2.4G WISP, AP, Mix. Please see below photo:

LTE Gateway

By default, it’s LTE Gateway mode, all you have to do is to insert 3G/4G SIM card, then the router will auto recognize and register to the corresponding network of 3G/4G. You can also custom and select your ISP.

Gateway

When you’re ready to use “Gateway” mode (standard wireless router mode), the WAN port of router should be connected to the modem via ethernet cable to dial.

Obtain an IP address automatically

Please go to System->Device->Operation Mode->Select “Gateway”->Confirm, then the router will reboot. Later please access the router from browser again, and go to Network->LAN-> Select “DHCP” from dropdown list of Dial Mode ->Click “Confirm” and then the router will obtain an IP address automatically from ISP.

Manually Set IP

Please go to System->Device->Operation Mode->Select “Gateway”->Confirm, then the router will reboot. Later please access the router from browser again, and go to Network->LAN->Select “Static IP” from dropdown list of Dial Mode ->Enter IP address, Subnet Mask, Gateway, DNS and other parameters you get from ISP->Click “Confirm"

PPPoE

Please go to System->Device->Operation Mode->Select “Gateway”->Confirm, then the router will reboot. Later please access the router from browser again, and go to Network->LAN-> Select “PPPoE” from dropdown list of Dial Mode ->Enter username, password and other parameters you get from ISP->Click “Confirm".

2.4G WISP

  • Please go to System->Device->Operation Mode->2.4G WISP;

  • Click “Scan” and it’ll pop up one dialog window of all searched wireless network, select one and enter username, password if required to connect.

AP

  • Please go to System->Device->Operation Mode->Select “AP”->Confirm. Try to connect the WAN port of V519 to the LAN port of the primary router via ethernet cable, then it can turn your wired network into wireless network.

Mix

In the Mix mode, it supports 4G, wired, wireless backup. When it’s failed to connect to network for main connection, the router will auto switch to the backup module to make sure the router can connect to the Internet normally.

  • Go to System->Device->Operation Mode->Select “Mix”;

  • After rebooting, go to Network->Connection->Set Main Connection as “LTE” and Alternate Connection as “WAN”:

  • Enter the corresponding parameters, click “confirm” and the router will reboot;

  • Insert SIM card and set parameters of 4G, and connected to 4G successfully;

  • Set wireless connection and enter related parameters:

  • Click “Interface” and you’ll see it’s all connected to 4G and WiFi:

✨